Power Supply

The power supply box is designed to safely supply a range of demanding energy consumers with power. It consists of industry standard components.

Battery box with typical installation
Battery Box with typical installation

Switching scheme

The battery box has a very simple design. Besides the cabling, it contains a solar charge regulator, a fuse panel for the protection of the consumers and an AGM 120aH battery.

Battery box switching scheme
Battery box switching scheme

Components

  • Sealable, durable Wham Bam Heavy Duty Box, 62 L, 59,5 x 40 x 37 cm, PP Recycling Plastic Wham Bam Box. The “Wham Bam Box” made of recycled PP plastic was chosen for its extreme mechanical strength and almost complete biochemical resistance. The bad temperature spectrum for thermal stability is from approx. -10 -140 °C., it is acid and alkali resistant and waterproof. By additionally equipping the box with a fire protection mat, the almost airtight closure offers a virtually complete reduction of fire load inside and outside the box.
  • 12V deep-cycle battery BSA Audio Solar Technologie 120 Ah 12V C100
  • 3 x Neutrik powerCON TRUE1 NAC3FPX outlets and Neutrik SCNAC-FPX sealing cover.
  • Fuse Box for car fuses up to max. 15A per fuse, maximum 30A per fuse box, With sealed cover, splash-proof, Material: PA6.6, 12 connections on the side
    • Nominal voltage: 32 V/DC
    • Nominal current (per output): 15 A
    • Temperature range: -20 - +85 °C
    • Connections: Flat plug 8x 6,3 x 0,8 mm lateral
  • Solar charge controller, 20A (ALLPOWERS, available from various brands) Specification ALLPOWERS

Wiring

  • Battery to solar charger:
    • Pole terminal connectors (+ and -)
    • 6 mm2 cables (red and black)
    • 2 x Crimp cable shoes
  • Solar panel to solar charger
    • MC4 photovoltaic connectors (+ and -) Weidemüller
    • 6 mm2 cables (red and black)
    • 2x Crimp cable shoes
  • Solar charger fuse box outlets
    • 6 x 1,5 mm2 cables, red
    • 6 x 1/4’’ FASTON terminals Fuse Box
    • 3 x 1,5 mm2 cables, black
    • 2 x Crimp cable shoes (holding 3 wires)
    • 6 x 6,35mm / 1/4’’ crimp FASTON terminals

Please note the following points:

  • Silicone cables, solar cables, plugs and fuse box fulfills industry standards. All cable lugs are crimped and checked.
  • The cable lugs are not screwed to the charging cables with cable lugs but through the crimp connection with the end sleeve.
  • A main fuse (e.g. 40A automatic circuit breaker) must be installed

See also the figure below.

Wiring details Fuse - Charger - Outlets Wiring details battery Setup of the Fuse
Wiring details Fuse - Charger - Outlets (left) Wiring details battery (right)

Mounting

  • Outlets: 6x M3 screw (12mm), washers and nuts
  • Solar connectors: 2 x waterproof cable glands
  • Solar charger and fuse box:
    • Wooden plate, glued to the box
    • 4 screws for Solar Charge Controller
    • 4 screws for fuse box Cable lugs and plugs are covered with self-vulcanizing tape and additionally insulated.

Station setup in the field

For safe operation, the following points must be taken into account when setting up the box:

1.) The box must be placed horizontally. Preferable at on a clearing to reduce impacts of falling branches or similar.

The box must be placed horizontally.

2.) One square meter around the box must be cleared of any vegetation and the A-horizon (depending on the slope, even more).

Cleaning box area and cable transects from organic material.

3.) Around this area a further strip with a diameter of at least 1 meter must also be cleared of organic material, especially leaves. Dig up the A-horizon and exclude roots and organic stuff. Note that the wiring sections must also be cleared of combustible organic material.

Clearing box area from vegetation and roots.

4.) Check cables and screws for proper seating and integrity.

Check cables and screws for proper seating and integrity.

5.) Check proper installation of the solar panel. Mount the panel on a simple wooden slat attached to the frame to avoid damage to the protective foil on the back. Such damage will destroy the panel.

Check proper installation of the solar panel.

6.) Attach the solar connectors to the panel. This avoids ground contact and provides good weather protection. This can be done very easily by threading cable ties through the plugs and the junction box.

Attach the solar connectors to the panel.

7.) Finally, the box should be secured against unauthorized or accidental opening. For this purpose there is a steel cable with a number lock, which is to be attached in the way it is placed there.

Secure box against unauthorized or accidental opening.

Final check

  1. All contacts and cables must be checked for proper seating and integrity. Especially the charging cables on the battery must be screwed tightly.
  2. All cables are to be laid without tension.
  3. The solar cables are to be laid separately to avoid a short circuit, so that an animal crossing etc. does not cause them to come into contact.
  4. The box is secured and tight.

Risk Assessment

Here you find the preliminary risk assesment for the installation and operation of 12 V solar power based energy supply units and measuring sensor systems.

Updated: